May
7
Started WFC at 0.5 Amp input again. WFC still leaking at the points where leads come out.
Pl check the following links for replication info about this WFC:
http://www.panaceauniversity.org/Ravi%20Cell.pdf
(For the circuit use the pg.25 schematic but with individual ferrite core rods straight wound for the Inductors rather than a single rod and bifilar wound–not recommended)
Forums:
http://www.oupower.com/phpBB2/viewtopic.php?t=1602
http://www.overunity.com/index.php/topic,3079.0.html
For Downloads of Water Fuel Cell Files:
http://www.hotlinkfiles.com/browse/srawofni/33693
(or)
http://www.hotlinkfiles.com/browse/waterfuel/42765
http://waterfuel.t35.com/wf_meyer_ravi.html
Dave Lawton Approved Shop for components & kits of WFC:
http://www.courtiestown.co.uk/batteries/shop.htm
R.
LESTER
Comments
25 Responses to “RAVI ‘S STANLEY MEYER REPLICATION WATER FUEL CELL -008”
Leave a Reply
You must be logged in to post a comment.
SCOTT
The wires youre talking about are from previous trials..theyre heat sinks and are not connected to anything…I just used the connectors at the bottom of that setup as I have 18 leads going into the WFC. Check the bifilar wound pics on overunity thread where you can see the new connectors are before and after the 9 inductors.
R.
THOMAS
are the mosfet transistors situated outside the box with blue lid? I noticed that you have 2 red +ve wires and a green -ve wire for supply. then you have other 2 yellow and 1 green wire coming out from that box. Are these these 3 wires going to 3 mosfets, and you are switching them alternatingly to drive the coils and cell?
REYES
I havent tried to measure the frequencies…it was done totally based on visual generation and volumetric measurements…the freq gen settings would vary with the water you use…I’ve tried different water from various sources..tap, stream, lake, underground(bore well),… the settings vary for all these…there is no thumb rule frequency as such. The tap water at your place would vary from mine due to the variation in the contaminants present…
JEWEL
why you say notting about the frequency you use ?
JAMISON
Its a 10A 12V DC converter from 240V AC mains. The freq gen would work even on a car battery so it doesnt matter where you get the DC input from. I’ve tried it with a car battery as input and it works fine.
R.
RONNY
Hello again Ravi. Can you give us specific details and specs of the power supply which you used to power your D 14 pulse generator circuit in the video? (brand name details if possible?)
What is the max amp range and impedance of your power supply? Thanks.
OMER
the one you see in the above vid is the D14 crt with the inductors…the VIC addition and bifilar winds on the inductors improved the efficiency even more…didnt post that info due to the risks involved
…but someone from panacea had posted the pics of my bifilar inductors generation on the overunity (dot) com thread….this addition increased the efficiency by 10CC for 20 secs at 0.5A 12V I/P to the freq gen. and there was further improvement with the VIC addition after this.
R.
MONROE
Will do.
RF…no…..the frequency of your WFC depends on the build and the water contaminants…sound complicated but once you build it its easy to find the right point for max generation after youve conditioned the tubes..
R.
JAN
As per Stans Canadian Patent… 2 parallel tubes are 3.75 times more efficient than plates and concentric tubes (ie more than 2 tubes) are 2.5 times more efficient than plates.
SS 316L seamless tubes are pretty expensive….you could try SS 304L seam less but the brown muck generation would not stop for a long time compared to 316L
R.
TAYLOR
Yes D14 crt …but add the VIC as per Stans US patent 4936961…he gives detailed specs of the VIC build.
R.
JEREMY
Check his vids….he does have something working including the vids of his intergration…nothing to lose I guess.
R.
ZACKARY
Also, do you use the circuit as described in the D14 PDF? I am thinking about building it, but I just want to make sure if that is the right one to build.
HAI
Does Meyer’s device work with flat stainless plates? I’m having trouble acquiring cheap SS tubes.
JOHNIE
I don’t know if we can take him seriously. Just look at his videos. “Weed under a microscope?”
HEATH
Hi Ravi. Let us know when they release their info if they are sucessful.
Are you using an RF frequency?
RAFAEL
Do a search of “bigfatpothead” on the youtube…he’s successfully integrated this unit to his vehicle and claims over 60% gain in mileage.
R.
JUAN
Panacea-Bocaf is doing an independent replication with four different units…once successful, detailed info which even a person with minimal engineering skills would be able tomake it. theyre making vids of these to be released for easier understanding.
R.
LYLE
i just cant wait for that day with a 100 percent sucessful replication with all the electronics disclosed for overunity production at 300 percent hmmm No more gasoline for me
RON
there are thousands of us trying to replicate the meyer effect we are getting closer we need to keep the info underground lets get our engines running for **** all . I think the voltage intensifier circuit needs further study
TREY
If you look at the specific resistance of SS 316L….its very very high…..it was working like a resistor. Once the length of the SS wire was shortened this problem was rectified.
R.
MARTY
if voltage potential is what is creating the gas then the wire would not have burnt like that. I think that there is a special currentat a specific freqency going on there that does this process
OREN
hhhm talk to me about it! i wanna know
PRESTON
Ive free sourced what I did & I dont intend to sell it aswell its free for everyone who can make it. You can find the them on oupower dot com and overunity dot com. Do a google search with ” ravi water fuel” youll find the exact threads on these forums and all the vids. Good Luck
R.
WILBERT
you people are all doing it wrong !!! use microwaves to hit that damm water it works !
KELLY
Try to use low voltage AC current and pulse that.